Free Newsletter

Be sure to register for your FREE Newsletter Below!






Lost Password?
No account yet? Register
National Cycle Peacemakers® Motorcycle Exhausts

National Cycle Peacemakers® Motorcycle Exhausts

The handlebar - mounted toggle switch controls the Actuator Motor and allows on-the-fly transitions between loud and quiet modes in just seconds! The slender chrome Actuator Motor , mounted to the right front downtube, receives the signal from the handlebar switch and opens/shuts the diverter valves within both mufflers via cables.


Plug Yourself In!

10th Power Media

Home
Denver Enforces Noisy Double Standards PDF Print E-mail

Denver Enforces Noisy Double Standards for Motorcyclists
By Astrid Bidanec

Big Gun Exhaust Quiet Series - Yamaha YFM660 Grizzly 02-04Denver, June 4th, 2007- City officials have approved changes to a law that might cause many bikers additional and unexpected expenses, while singling them out for unfair treatment, according to the American Motorcyclists Association (AMA).

Denver’s revised vehicle noise ordinance, now allows police to issue tickets to riders in the city if their motorcycles, including models dating as far back as 1982, don't have a federal Environmental Protection Agency sound-certification label on the exhaust systems.

Naturally, this excludes all custom built motorcycles, since the original exhaust has to be installed by the manufacturer. Violators are given two weeks to correct the problem, or they are fined $500.

In spite of the inclusion of all motor vehicles by the Denver ordinance, only motorcycles would be subject to the EPA sound certification labeling requirement, which is an addition to the already performed sound test.

Motorcyclists are faced with the choice of paying the fine, or spending their cash on the approved manufacturer’s exhausts. Motor Vehicle owners in comparison are free to purchase their replacement mufflers at less expensive retailers, like Midas or Meineke. This creates an unfair standard in the eyes of the AMA.

"We understand the motivation for cities to pass laws controlling sound levels from traffic," said Ed Moreland, AMA Vice President for Government Relations. "But the approach being taken in Denver creates a special class of enforcement that unfairly targets motorcyclists. Loud trucks and cars are every bit as annoying as loud motorcycles, but only motorcyclists would be subject to this new provision of the labeling law."

While the new regulation has been in effect since July 1,st the AMA plans to appeal it and collaborate with the City Council to create a new solution to the noise problem.

"We look forward to working with the Denver City Council to come up with a more reasonable solution for dealing with excessive sound levels from traffic," Moreland said. "Our experience has shown that there are a range of approaches cities can take to this issue without imposing restrictive laws on motorcyclists."

The AMA has successfully worked with the city of Albuquerque, New Mexico, in the past to rescind a similarly unfair provision. Moreover, it has hosted national summits uniting bikers, manufacturers, law enforcement and government officials to overcome the disturbance of excessive motorcycle noise.

Source: http://home.ama-cycle.org/newsroom/amarelease.asp?rnum=A07009

 
< Prev   Next >



Motorcycle Engine Dress-Up Kit

Motorcycle Engine Dress-Up Kit

All components are made of stamped steel, chrome-plated to a show-quality luster Here are the "goodies" you'll need to brighten and enhance your engine in one money-saving kit! Don't customize your engine one piece at a time—this kit saves you time and money Kit includes oil pump cover, tappet block covers (a pair) and oil filter housing cover. Will not fit Sportster models. Parts can also be purchased individually. Oil Pump Cover. Slips on easily.Mounting hardware included. Tappet Block Covers (a pair). Look like stock.



Clamp-On Folding Motorcycle Foot Pegs

Clamp-On Folding Motorcycle Foot Pegs

Black rubber-covered foot pegs give your feet a place to rest comfortably Fold up and out of the way when not needed Die-cast polished aluminum clamps fit 1" diam. round bars on all popular OEM and replacement engine guards and case guards Clamps have recessed Allen head bolts for a smooth, clean look. Include 1" clamp mount. Sold in pairs.



| Home | | News | | Forum | | Articles | | Links | | Contact | | Advertise | | Disclaimer |
© 2009 Motorcycle Restorer Monthly
Another 10th Power Media Production